Regulations 2008
Syllabus
SEMESTER I
(Common to all B.E. / B.Tech. Degree Programmes)
HS1101 - TECHNICAL ENGLISH I
L T P C
3 1 0 4
UNIT I FOCUS ON LANGUAGE: VOCABULARY 9+3
General Vocabulary - Changing words from one form to another - Nouns – Compound nouns –
Adjectives, Comparative adjectives - Adverbs – Adverb forms – Prefixes and Suffixes –
Spelling and Punctuation – British and American vocabulary .
UNIT II FOCUS ON LANGUAGE: GRAMMAR 9+3
Subject-Verb Agreement - Tenses – Present Tense – Past Tense – Future Tense - Active and
Passive Voice – Gerunds and Infinitives - Cause and Effect Expressions – ‘If’ conditionals –
Correction of Errors.
UNIT III READING 9+3
Skimming for gist – Scanning for specific information – Inference – Reading in Context –
Intensive Reading - Graphic Presentation: Bar Chart and Flow Chart – Sequencing of
Sentences.
UNIT IV WRITING 9+3
Paragraph Writing – Description – Comparison and Contrast – Definition – Instructions –
Formal Letter Writing – Letters to the Editor – Accepting and Declining an Invitation –
Permission Letter.
UNIT V LISTENING AND SPEAKING 9+3
Listening and transfer of information – Listening and Note-taking – Creative Thinking and
Speaking – Conversation Techniques - Persuasive Speaking – Group Discussion and Oral
Reports - Speaking about Future Plans.
L: 45 T: 15 Total: 60
TEXT BOOK
1. Meenakshi Raman and Sangeeta Sharma, ‘Technical Communication: English Skills
for Engineers’, New Delhi: Oxford University Press, 2008.
REFERENCES
1. Department of Humanities and Social Sciences, Anna University, ‘English for
Engineers and Technologists’ Combined Edition (Volumes 1 and 2), Chennai: Orient
Longman Pvt. Ltd., 2006. Themes 1 – 4 (Resources, Energy, Computer, Transport)
2. Andrea, J. Rutherford, ‘Basic Communication Skills for Technology’, Second Edition,
Pearson Education, 2007.
MA1101 - MATHEMATICS I
L T P C
3 1 0 4
UNIT I MATRICES 9+3
Characteristic equation – Eigen values and Eigen vectors of a real matrix – Properties of Eigen
values – Problem solving using Cayley-Hamilton theorem – Similarity transformation –
Orthogonal transformation of a symmetric matrix to diagonal form – Quadratic form –
Orthogonal reduction to its canonical form.
UNIT II THREE DIMENSIONAL GEOMETRY 9+3
Angle between two lines – Coplanar lines – Shortest distance between skew lines – Equation of
a sphere – Plane section of a sphere – Tangent plane – Orthogonal Spheres - Equation of a
cone – Right circular cone – Equation of a cylinder – Right circular cylinder.
UNIT III DIFFERENTIAL CALCULUS 9+3
Curvature – Cartesian and Parametric Co-ordinates – Centre and Radius of curvature – Circle
of curvature – Envelopes – Evolutes.
UNIT IV FUNCTIONS OF SEVERAL VARIABLES 9+3
Partial derivatives – Euler’s theorem for homogeneous functions – Total derivative –
Differentiation of implicit functions – Jacobians – Maxima / Minima for functions of two
variables – Method of Lagrange’s multipliers – Taylor’s expansion.
UNIT V ORDINARY DIFFERENTIAL EQUATIONS (ODE) 9+3
Solution of second and higher order linear ODE with constant coefficients – Simultaneous first
order linear equations with constant coefficients – Linear equations of second order with
variable coefficients – Cauchy’s and Legendre’s linear equations – Method of variation of
parameter.
L: 45 T: 15 Total: 60
TEXT BOOKS
1. Grewal, B.S, “Higher Engineering Mathematics”, Thirty eighth Edition, Khanna
Publishers, New Delhi, 2005.
2. Venkataraman. M. K., “Engineering Mathematics”, Volume I and II Revised enlarged
Fourth Edition, The National Publishing Company, Chennai, 2004.
REFERENCES
1. Glyn James., “Advanced Modern Engineering Mathematics”, Third Edition, Pearson
Education Ltd, New Delhi, 2004.
2. Veerarajan. T., “Engineering Mathematics (for first year)”, Fourth Edition, Tata
McGraw – Hill Publishing Company Limited, New Delhi, 2005.
3. Bali N. P and Manish Goyal, “Text book of Engineering Mathematics”, Third edition,
Laxmi Publications (P) Ltd., 2008.
HS1102 - ENGINEERING PHYSICS I
L T P C
3 0 0 3
UNIT I ULTRASONICS 9
Introduction – Production – magnetostriction effect - magnetostriction generator - piezoelectric
effect - piezoelectric generator- Detection of ultrasonic waves properties - Cavitations -
Velocity measurement – Acoustic Grating - SONAR - Non Destructive Testing - Pulse echo
system through transmission and reflection modes - A, B and C - scan displays – Applications
of Ultrasonics - Industrial and Medical - Sonogram
UNIT II LASERS 9
Introduction – Principle of Spontaneous emission and stimulated emission. Population
inversion, pumping. Einsteins A and B coeffcients - derivation. Types of lasers – He - Ne,
CO2, Nd -YAG, Semiconductor lasers (homojunction and heterojunction) - Qualitative
Industrial and Medical applications of Lasers - Holography – Construction and reconstruction
of a Hologram- applications of a Hologram
UNIT III FIBRE OPTICS 9
Principle and propagation of light in optical fibres – Numerical aperture and Acceptance angle
- Types of optical fibres (material, refractive index, mode) – Double crucible technique of
fibre drawing - Losses in an optical fibre – Attenuation, Dispersion and Bending losses - Fibre
optical communication system (Block diagram) - Light sources and detectors - Fibre optic
sensors – Temperature and Displacement Sensors - Endoscope.
UNIT IV QUANTUM PHYSICS 9
Black body radiation – Planck’s theory (derivation) – Deduction of Wien’s displacement law
and Rayleigh – Jeans’ Law from Planck’s theory – Compton effect -Theory and experimental
verification – Matter waves - Electron microscope – Schrödinger’s wave equation – Time
independent and time dependent equations – Physical significance of wave function – Particle
in a one dimensional box – Electrons in a metal - Degeneracy
UNIT V CRYSTAL PHYSICS 9
Lattice – Unit cell – Bravais lattice – Lattice planes – Miller indices – Interplanar spacing ‘d’
in a cubic lattice – Calculation of number of atoms per unit cell – Atomic radius –
Coordination number – Packing factor for SC, BCC, FCC and HCP structures – NaCl, ZnS,
Diamond and Graphite structures.
Total: 45
TEXT BOOKS
1. R. K. Gaur and S.C. Gupta, ‘Engineering Physics’ Dhanpat Rai Publications, 2003.
2. M.N. Avadhanulu and PG Kshirsagar, ‘A Text book of Engineering Physics’, S.Chand
and Company, Ltd., New Delhi, 2005.
REFERENCES
1. Chitra Shadrach and Sivakumar Vadivelu, ‘Engineering Physics’, Pearson Education,
2007.
2. Serway and Jewett, ‘Physics for Scientists and Engineers with Modern Physics’, 6th
Edition, Thomson Brooks/Cole, Indian reprint 2007.
3. Arumugam, M, ‘Engineering Physics’, Anuradha Publishers, Kumabakonam 2005.
4. Palanisamy, P.K., ‘Engineering Physics’ Scitech publications, 2007.
5. Rajendran, V and Marikani A, ‘Engineering Physics’ Tata Mc Graw Hill Publications
Ltd, III Edition, 2004.
HS1103 - ENGINEERING CHEMISTRY I
L T P C
3 0 0 3
UNIT I WATER TREATMENT PROCESS 9
Alkalinity -Types of alkalinity and determination –- Hardness - Types - CaCO3 equivalents -
Estimation by EDTA method (problem) –- Boiler feed water – requirements - Troubles of
using hard water in boilers –-Internal conditioning (phosphate, calgon and carbonate) -
External conditioning - Zeolite process –-Domestic water treatment - Disinfection methods
(Chlorination, UV treatment and ozonation) –- Desalination - Reverse osmosis.
UNIT II SURFACE CHEMISTRY 9
Adsorption - Types –- Adsorption of gases on solids –- Adsorption isotherms – Frendlich and
Langmuir isotherms –- Adsorption of solutes from solutions –- Role of adsorbents in catalysis
–- Ion-exchange adsorption and Pollution abatement.
UNIT III ELECTROCHEMISTRY 9
Electrochemical cells – Reversible and irreversible cells –- EMF - measurement of emf –
Electrode potential – Nernst equation (problem) –- Reference electrodes - Standard hydrogen
electrode - Calomel electrode - Glass electrode - Quinhydrone electrode and measurement of
pH –- Electrochemical series - significance –- Conductometric titrations (HCl - NaOH
titration) –- Potentiometric titrations (redox - Fe2+ vs dichromate and precipitation - Ag+ vs Cltitrations).
UNIT IV ENERGY SOURCES AND STORAGE DEVICES 9
Nuclear energy - Nuclear fission and fusion process –- Nuclear reactor - Light water nuclear
power plant (block diagram only) - Breeder reactor –- Batteries - Alkaline battery - Lead acid
storage battery - Nickel-Cadmium battery - Lithium batteries - Fuel cells - hydrogen-oxygen
fuel cell –-Solar energy conversion - Solar cells - Wind energy.
UNIT V ANALYTICAL TECHNIQUES 9
Beer-Lambert’s law (problem) –- UV-Visible and IR spectroscopy - Principle and
Instrumentation (problem) (block diagram only) –- Estimation of iron by colorimetric analysis
–- Flame photometry - Principle and Instrumentation (block diagram only) – Estimation of
sodium by flame photometry –- Atomic absorption spectroscopy - Principle and
Instrumentation (block diagram only) – Estimation of Nickel by atomic absorption
spectroscopy.
L: 45 Total: 45
TEXTBOOKS
1. P.C. Jain and Monika Jain, “Engineering Chemistry”, 15th Edition, Dhanpat Rai
Publishing Company (P) Ltd., New Delhi, 2007.
2. S. Bahl, G.D. Tuli and Arun Bahl, “Essentials of Physical Chemistry”, S. Chand and
Company Ltd., New Delhi, 2004.
REFERENCES
1. J.C. Kuriakose and J. Rajaram, “Chemistry in Engineering and Technology”, Vol.1 and
2, Tata Mcgraw Hill Publishing Company (P) Ltd., New Delhi, 1996.
2. B.K. Sharma, “Engineering Chemistry”, Krishna Prakasam Media (P) Ltd., Meerut,
2001.
3. B. Sivasankar “Engineering Chemistry” Tate McGraw-Hill Pub.Co.Ltd, New Delhi
(2008).
ME1101 - ENGINEERING GRAPHICS
L T P C
2 3 0 5
Concepts and conventions (Not for Examination) 1
Importance of graphics in engineering applications – Use of drafting instruments – BIS
conventions and specifications – Size, layout and folding of drawing sheets – Lettering and
dimensioning.
UNIT I PLANE CURVES AND FREE HAND SKETCHING 15
Curves used in engineering practices:
Conics – Construction of ellipse, Parabola and hyperbola by eccentricity method –
Construction of cycloid – construction of involutes of squad and circle – Drawing of tangents
and normal to the above curves.
Free hand sketching:
Representation of Three Dimensional objects – General principles of orthographic projection –
Need for importance of multiple views and their placement – First angle projection – layout
views – Developing visualization skills through free hand sketching of multiple views from
pictorial views of objects.
UNIT II PROJECTION OF POINTS, LINES AND PLANE SURFACES 14
Projection of points and straight lines located in the first quadrant – Determination of true
lengths and true inclinations – Projection of polygonal surface and circular lamina inclined to
both reference planes.
UNIT III PROJECTION OF SOLIDS 15
Projection of simple solids like prisms, pyramids, cylinder and cone when the axis is inclined
to one reference plane by change of position method.
UNIT IV SECTION OF SOLIDS AND DEVELOPMENT OF SURFACES 15
Sectioning of above solids in simple vertical position by cutting planes inclined to one
reference plane and perpendicular to the other – Obtaining true shape of section.
Development of lateral surfaces of simple and truncated solids – Prisms, pyramids, cylinders
and cones – Development of lateral surfaces of solids with cylindrical cutouts, perpendicular to
the axis.
UNIT V ISOMETRIC AND PERSPECTIVE PROJECTIONS 15
Principles of isometric projection – isometric scale – isometric projections of simple solids,
truncated prisms, pyramids, cylinders and cones.
Perspective projection of prisms, pyramids and cylinders by visual ray method.
L: 30 T: 45 Total: 75
TEXT BOOKS
1. K. V. Natrajan, “A text book of Engineering Graphics”, Dhanalakshmi Publishers,
Chennai (2006).
2. M.B. Shah and B.C. Rana, “Engineering Drawing”, Pearson Education (2005).
REFERENCES
1. N.D. Bhatt, “Engineering Drawing” Charotar Publishing House, 46th Edition, (2003).
2. Luzadder and Duff, ‘Fundamentals of Engineering Drawing’, Prentice Hall of India
Pvt. Ltd. 11th Edition, 2001
3. Dhananjay A.Jolhe, “Engineering Drawing with an introduction to AutoCAD” Tata
McGraw Hill Publishing Company Limited (2008).
Publication of Bureau of Indian Standards:
1. IS 10711 – 2001: Technical products Documentation – Size and lay out of drawing
sheets.
2. IS 9609 (Parts 0 and 1) – 2001: Technical products Documentation – Lettering.
3. IS 10714 (Part 20) – 2001 and SP 46 – 2003: Lines for technical drawings.
4. IS 11669 – 1986 and SP 46 – 2003: Dimensioning of Technical Drawings.
5. IS 15021 (Parts 1 to 4) – 2001: Technical drawings – Projection Methods.
Special points applicable to University Examinations on Engineering Graphics:
1. There will be five questions, each of either or type covering all units of the syllabus.
2. All questions will carry equal marks of 20 each making a total of 100.
3. The answer paper shall consist of drawing sheets of A3 size only. The students will be
permitted to use appropriate scale to fit solution within A3 size.
4. Whenever the total number of candidates in a college exceeds 150, the University
Examination in that college will be conducted in two sessions (FN and AN on the same
day) for 50 percent of students (approx) at a time.
CS1101 - FUNDAMENTALS OF COMPUTING AND PROGRAMMING
L T P C
3 1 0 4
UNIT I DIGITAL CONCEPTS 9+3
Digital Computer Fundamentals – Block diagram of a computer – Components of a computer
system – Digital and Analog quantities – Binary digits – Logic Levels – Digital Waveforms –
Basic Logic operations – Digital Integrated Circuits.
UNIT II NUMBER SYSTEMS 9+3
Number Representation – Decimal, Binary, Octal, Hexadecimal and BCD numbers – Binary
Arithmetic – Binary addition – Unsigned and Signed numbers – one’s and two’s complements
of Binary numbers – Arithmetic operations with signed numbers - Number system conversions
– Digital codes.
UNIT III HARDWARE AND SOFTWARE 9+3
Processing Devices – Memory Devices – Input and Output Devices – Optical Input Devices –
Audiovisual Input Devices – Monitors – Printing Devices - Storage Devices – Magnetic and
Optical Storage Devices - System Software – Application Software – Graphics and
Multimedia.
UNIT IV NETWORKING FUNDAMENTALS 9+3
Overview of Data Communication with Standard Telephone Lines and Modems, Digital Data
Connections, Broadband Connections, DSL Technologies and Cable Modem Connections –
Computer Networking Basics – Common Types of Networks – Structuring of Networks –
Network Media and Hardware.
UNIT V PROBLEM SOLVING AND C PROGRAMMING 9+3
Planning the Computer Program – Purpose – Algorithm – Flow Charts – Pseudocode –
Programming fundamentals – Variables and Data Types – Constants – Preprocessor –
Operators and Expressions – Managing Input and Output operators – Decision Making –
Branching and Looping – User-defined Functions – Declarations – Call by reference – Call by
value – Arrays – Pointers – Handling of Character Strings – Structures and Unions.
L: 45 T: 15 Total: 60
TEXT BOOKS
1. Thomas L.Floyd and R.P.Jain,“Digital Fundamentals”,8th Edition, Pearson
Education,2007.
2. Peter Norton “Introduction to Computers”,6th Edition, Tata Mc Graw Hill, New
Delhi,2006.
3. Ashok.N.Kamthane, “Computer Programming”, Pearson Education (India), 2008.
REFERENCES
1. Behrouz A. Forouzan and Richard.F.Gilberg, “A Structured Programming Approach
Using C”, II Edition, Brooks-Cole Thomson Learning Publications, 2007.
2. Morris Mano, “Digital Design”, 3rd Edition, Pearson Education, 2006.
3. Albert Paul Malvino, Donald P. Leech, “Digital Principles and Applications”, 6th
Edition, Mc Graw Hill Publishers, 2007.
CS1102 - COMPUTER PRACTICE LABORATORY I
L T P C
0 0 3 2
LIST OF EXERCISES
Concepts Suggested Exercises
UNIT I
Introduction to Application
Packages
Practical Exercises may be given in the application packages to
acquire skills in word processing ,Spread sheet and Power Point.
Word
1. Document creation, Text manipulation with Scientific
notations.
2. To create an advertisement in word.
3. To illustrate the concept of mail merging, importing images,
tables in word.
4. Drawing - flow Chart
Spreadsheet
5. Chart - Line, XY, Bar and Pie.
6. Formula - formula editor.
7. Spread sheet - inclusion of object, Picture and graphics,
protecting the document and sheet
8. To create a spread sheet to analyze the marks of the students
of a class and also to create appropriate charts.
9. Sorting and Import / Export features.
Power Point
10. To create the presentation for the department with Power
Point using animation, Design Templates and Effective
presentation.
UNIT II
C Programming Basics* The following exercises may be suggested
Data types, Expression
Evaluation, Condition
Statements,Operators and
Expressions
11. To write a simple menu driven calculator program using
switch statement,
12. To Find Age in terms of years, months and days.
IO Formatting 13. To print multiplication table for the given number.
Decision Making 14. To check and print if the given number is a palindrome or not,
and the given number is a prime number or not
Looping To print Fibonacci and Trigonometric series.
UNIT III
Exercises may be given to understand function prototype and
invocation procedures, to understand call by value, call by
address and implement recursion.
Arrays
15. To find the largest and smallest number using array
16. To Sort numbers in an array in ascending / Descending order.
17. To implement bubble sorting.
18. To reverse the elements given in an array.
19. Write a program for matrix addition and multiplication
String Manipulations 20. To implement string manipulation functions without using
library functions.
21. To arrange the names in alphabetic order.
Functions 22. To perform sequential search using functions.
Recursions 23. To find the factorial of a number using recursion.
UNIT IV
Structures and Unions
24. To print the marksheet of ‘n’ students using structures.
Pointers 25. To print the elements of an array using pointers and String
manipulation.
Files 26. To print the marksheet of ‘n’ students using file handling
operations.
UNIT V
Command line arguments 27. To merge two files using command line arguments.
Total:45
* For programming exercises Flow chart and Pseudo code are essential
HARDWARE / SOFTWARE REQUIRED FOR A BATCH OF 30 STUDENTS
Hardware
LAN System with 33 nodes (OR) Standalone PCs – 33 Nos.
Printers – 3 Nos.
Software
OS – Windows / UNIX Clone
Application Package – Office suite
Compiler – C
GE1101 - ENGINEERING PRACTICES LABORATORY
L T P C
0 0 3 2
GROUP A (CIVIL AND MECHANICAL)
I CIVIL ENGINEERING PRACTICE 9
Buildings:
(a) Study of plumbing and carpentry components of residential and industrial buildings.
Safety aspects.
Plumbing Works:
(a) Study of pipeline joints, its location and functions: valves, taps, couplings, unions,
reducers, elbows in household fittings.
(b) Study of pipe connections requirements for pumps and turbines.
(c) Preparation of plumbing line sketches for water supply and sewage works.
(d) Hands-on-exercise:
Basic pipe connections – Mixed pipe material connection – Pipe connections with different
joining components.
(e) Demonstration of plumbing requirements of high-rise buildings.
Carpentry using Power Tools only:
(a) Study of the joints in roofs, doors, windows and furniture.
(b) Hands-on-exercise:
Wood work, joints by sawing, planning and cutting.
II MECHANICAL ENGINEERING PRACTICE 13
Welding:
(a) Preparation of arc welding of butt joints, lap joints and tee joints.
(b) Gas welding practice.
Basic Machining:
(a) Simple turning and Taper turning.
(b) Drilling practice.
Sheet Metal Work:
(a) Forming and Bending:
(b) Model making – Trays, Funnels, etc.
(c) Different type of joints.
Machine assembly practice:
(a) Study of centrifugal pump.
(b) Study of air conditioner.
Demonstration on:
(a) Smithy operations, upsetting, swaging, setting down and bending. Example – Exercise
– Production of hexagonal headed bolt.
(b) Foundry operations like mould preparation for gear and step cone pulley.
(c) Fitting – Exercises – Preparation of square fitting and vee – fitting models.
GROUP B (ELECTRICAL AND ELECTRONICS)
III ELECTRICAL ENGINEERING PRACTICE 10
1. Residential house wiring using switches, fuse, indicator, lamp and energy meter.
2. Fluorescent lamp wiring.
3. Stair-case wiring.
4. Measurement of electrical quantities – voltage, current, power and power factor in RLC
circuit.
5. Measurement of energy using single phase energy meter.
6. Measurement of resistance to earth of an electrical equipment.
IV ELECTRONICS ENGINEERING PRACTICE 13
1. Study of Electronic components and equipments – Resistor, colour coding
measurement of AC signal parameter (peak-peak, rms period, frequency) using CR.
2. Study of logic gates AND, OR, EOR and NOT.
3. Generation of Clock Signal.
4. Soldering practice – Components Devices and Circuits – Using general purpose PCB.
5. Measurement of ripple factor of HWR and FWR.
P : 22+23 Total : 45
REFERENCES
1. K.Jeyachandran, S.Natarajan and S, Balasubramanian, “A Primer on Engineering
Practices Laboratory” , Anuradha Publications, 2007.
2. T.Jeyapoovan, M.Saravanapandian and S.Pranitha, “Engineering Practices Lab
Manual”, Vikas Puplishing House Pvt.Ltd, 2006
3. H.S. Bawa, “Workshop Practice”, Tata McGraw – Hill Publishing Company Limited,
2007.
4. A. Rajendra Prasad and P.M.M.S. Sarma, “Workshop Practice”, Sree Sai Publication,
2002.
5. P.Kannaiah and K.L.Narayana, “Manual on Workshop Practice”, Scitech Publications,
1999.
SEMESTER EXAMINATION PATTERN
The Laboratory examination is to be conducted for Group A and Group B, allotting 90 minutes
for each group, with a break of 15 minutes. Both the examinations are to be taken together in
sequence, either in the FN session or in the AN session. The maximum marks for Group A and
Group B lab examinations will be 50 each, totaling 100 for the Lab course. The candidates
shall answer either I or II under Group A and either III or IV under Group B, based on lots.
Engineering Practices Laboratory- List of equipment and components
(For a Batch of 30 Students)
CIVIL
1. Assorted components for plumbing consisting of metallic pipes,
plastic pipes, flexible pipes, couplings, unions, elbows, plugs and
other fittings. 15 Sets.
2. Carpentry vice (fitted to work bench) 15 Nos.
3. Standard woodworking tools 15 Sets.
4. Models of industrial trusses, door joints, furniture joints 5 each.
5. Power Tools: (a) Rotary Hammer 2 Nos.
(b) Demolition Hammer 2 Nos.
(c) Circular Saw 2 Nos.
(d) Planer 2 Nos.
(e) Hand Drilling Machine 2 Nos.
(f) Jigsaw 2 Nos.
MECHANICAL
1. Arc welding transformer with cables and holders 5 Nos.
2. Welding booth with exhaust facility 5 Nos.
3. Welding accessories like welding shield, chipping hammer,
wire brush, etc. 5 Sets.
4. Oxygen and acetylene gas cylinders, blow pipe and other
welding outfit. 2 Nos.
5. Centre lathe 2 Nos.
6. Hearth furnace, anvil and smithy tools 2 Sets.
7. Moulding table, foundry tools 2 Sets.
8. Power Tool: Angle Grinder 2 Nos.
9. Study-purpose items: centrifugal pump, air-conditioner 1 each.
ELECTRICAL
1. Assorted electrical components for house wiring 15 Sets.
2. Electrical measuring instruments 10 Sets.
3. Study purpose items: Iron box, fan and regulator, emergency lamp 1 each.
4. Megger (250V/500V) 1 No.
5. Power Tools: (a) Range Finder 2 Nos.
(b) Digital Live-wire detector 2 Nos.
ELECTRONICS
1. Soldering guns 10 Nos.
2. Assorted electronic components for making circuits 50 Nos.
3. Small PCBs 10 Nos.
4. Multimeters 10 Nos.
5. Study purpose items: Telephone, FM radio, low-voltage power supply
HS1104 - PHYSICS CHEMISTRY LABORATORY I
L T P C
0 0 3 -
PHYSICS LABORATORY I
LIST OF EXPERIMENTS
1. (a) Particle size determination using Diode Laser.
(b) Determination of Laser parameters – Wavelength, and Angle of divergence.
(c) Determination of Acceptance angle in an Optical Fiber.
2. Determination of thickness of a thin wire – Air wedge method.
3. Determination of velocity of sound and compressibility of liquid – Ultrasonic
Interferometer.
4. Determination of wavelength of Mercury spectrum – Spectrometer grating.
5. Determination of thermal conductivity of a bad conductor – Lee’s Disc method.
6. Determination of Hysteresis loss in a Ferromagnetic material.
CHEMISTRY LABORATORY I
LIST OF EXPERIMENTS
1. Estimation of Hardness of Water by EDTA method.
2. Estimation of Copper in brass by EDTA method.
3. Determination of DO in water by Winkler’s method.
4. Estimation of Chloride in Water sample by Argentometric method.
5. Estimation of alkalinity of Water sample.
6. Determination of molecular weight and degree of polymerization using Viscometry.
• A minimum of FIVE experiments shall be offered.
• Laboratory classes on alternate weeks for Physics and Chemistry.
• The lab examinations will be held only in the second semester
No comments:
Post a Comment